Type: Driver
File Name:
File Size: 8.0 MB
85 (4.78)
Downloads: 64
Supported systems: ALL Windows 32x/64x
Price: Free* (*Free Registration Required)

Download Now

Summary of product 5. Disassembly and Reassembly 6.


Alignment and Adjustments xerox pe16 scanner. Troubleshooting 8. Exploded Views and Parts List 9. Block Diagram Connection Diagram. Precautions Product Terms Caution: A personal injury hazard exists that may not be apparent.

For example, a panel may cover the hazardous area. Danger: A personal injury hazard exists in the area where you see the sign. Symbols Marked on the Product Hot surface xerox pe16 scanner or in the printer. Use caution to avoid personal injury. Use caution or draws attention to a particular component.

gateway solo9300Can you help with this problem?
sy ms8518xerox pe16\scanner locked
jhf printerScanning Problems
mexxcom camPublisher's Description

Refer to the manual s for information. Class I laser products are not considered to be hazardous. The laser system and printer are designed so there is xerox pe16 scanner any human access to laser radiation above a Class I level during normal operation, user maintenance, or prescribed service condition. The reflected beam, although invisible, can damage your eyes.

When using this product, these basic safety precautions should always be followed to reduce risk of fire, electric shock, and injury to persons. Use only the specified power cord xerox pe16 scanner connector. For VAC units, do not apply more than volts RMS between the supply conductors or between either supply conductor and ground.


Use only the specified power cord. This manual assumes that the reader is a qualified service technician.

Xerox scanner..

Plug the three-wire power cord with grounding prong into a grounded AC outlet only. If necessary, contact a licensed electrician to install a properly grounded outlet. If the product loses its ground connection, contact with conductive parts may cause an electrical shock. You must also disconnect the unit power cord from the AC outlet. Position the power cord so that it is easily accessible during servicing so that you may power down the unit during an emergency. Xerox pe16 scanner the power plug by pulling the plug, not the cord. Disconnect the power cord in the following cases:. The following techniques will reduce the occurrence of component damage caused by static electricity. Be sure the power to the chassis or circuit board is off, and observe all other safety precautions. Before handling any semiconductor components assemblies, drain the electrostatic charge from your body.

This can be accomplished by touching an earth ground source or by wearing a xerox pe16 scanner strap device connected to an earth ground source. Wearing a wrist strap will also prevent accumulation of additional bodily static charges. Be sure to remove the wrist strap before applying power to the unit to avoid potential shock.


After removing a xerox pe16 scanner sensitive assembly from its anti-static bag, place it on a grounded conductive surface. If the anti-static bag is conductive, you may ground the bag and use it as a conductive surface. Do not use freon-propelled chemicals, as they can generate electrical charges that may damage some devices. Do not remove a static sensitive replacement component or electrical subassembly from its protective package until you are ready to install it. Before removing the protective material from the leads of a replacement device, touch the protective material to the chassis or circuit assembly into which the device will be installed. Minimize body motions when handling unpackaged replacement devices. Simple motions such as your clothes brushing together or lifting a foot from a carpeted floor can generate enough static electricity to damage a static sensitive device Handle ICs and EPROMs carefully to avoid bending pins.

Service Safety Summary General Guidelines Note The material presented here is intended as a safety reminder for qualified service personnel. Refer also to the preceding Power Safety Precautions. Avoid servicing alone: Xerox pe16 scanner not perform internal service or adjustment of this product unless another person capable of rendering first aid or resuscitation is present.

Scanners not supported by SANE

Use care when servicing with power: Dangerous voltages may exist at several points in this product. To avoid personal injury, do not touch exposed connections and components while power is on. Disconnect power before removing the power supply shield or replacing components.File xerox pe16 scanner for WorkCentre PE16/i. File Download: WorkCentre PE 16 Scanner Driver.

Filename TWAIN scanner driver for the Xerox WorkCentre PE 0. 15, Jan 1, · #2 · workcentre-pe16/downloads/?operatingSystem=win7x

Related Posts